CVE-2026-98761 Affecting linux-6.12 package, versions <6.12.113-1~deb12u1


Severity

Recommended
low

Based on default assessment until relevant scores are available.

Threat Intelligence

EPSS
0.17% (6th percentile)

Do your applications use this vulnerable package?

In a few clicks we can analyze your entire application and see what components are vulnerable in your application, and suggest you quick fixes.

Test your applications
  • Snyk IDSNYK-DEBIAN12-LINUX612-21434722
  • published23 Oct 2026
  • disclosed18 Oct 2026

Introduced: 18 Oct 2026

NewCVE-2026-98761  (opens in a new tab)

How to fix?

Upgrade Debian:12 linux-6.12 to version 6.12.113-1~deb12u1 or higher.

NVD Description

Note: Versions mentioned in the description apply only to the upstream linux-6.12 package and not the linux-6.12 package as distributed by Debian. See How to fix? for Debian:12 relevant fixed versions and status.

In the Linux kernel, the following vulnerability has been resolved:

usb: typec: tcpm: recover after failure to start the frs ams

Reset the port if the tcpm fails to start the FAST_ROLE_SWAP AMS by initiating error recovery on it.

This helps in cases where some cables (incorrectly) signal an FRS to an FRS capable port during disconnection. The TCPC autonomously starts sourcing VBUS on detecting the FRS signal. However, the VBUS sourcing is left on when the FAST_ROLE_SWAP AMS fails to start (as tcpm_sink_tx_ok is 0 as CC is open due to the cable disconnect). This is because the code sets the state to INVALID_STATE without resetting the port state.

Log snippet before changes: [ 101.401960] AMS FAST_ROLE_SWAP start [ 101.401971] Sink TX No Go [ 101.401982] sourcing vbus [ 101.401987] VBUS on [ 101.402159] VBUS on [ 109.257809] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_READY, polarity 1, disconnected] [ 111.267442] VBUS on

After changes: [ 70.541211] AMS FAST_ROLE_SWAP start [ 70.541220] Sink TX No Go [ 70.541228] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS] [ 70.541362] VBUS on [ 70.541365] sourcing vbus [ 70.541367] VBUS on [ 70.541374] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS] [ 70.541410] disable vbus discharge ret:0 [ 70.543028] Setting usb_comm capable false [ 70.544009] Setting voltage/current limit 0 mV 0 mA [ 70.544034] polarity 0 [ 70.544239] Requesting mux state 0, usb-role 0, orientation 0 [ 70.555550] cc:=0 [ 70.555595] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS] [ 70.555697] VBUS off [ 70.555702] VBUS VSAFE0V [ 70.555762] CC1: 5 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected] [ 70.587794] VBUS off [ 70.587799] VBUS VSAFE0V [ 70.655672] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms] [ 70.655682] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev3 NONE_AMS] [ 70.655686] Start toggling [ 70.656274] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]

CVSS Base Scores

version 3.1